ATV310 (Altivar Easy)
range of product | Easy Altivar 310 | |
---|---|---|
product or component type | Variable speed drive | |
product specific application | Simple machine | |
assembly style | With heat sink | |
device short name | ATV310 | |
network number of phases | Three phase | |
[Us] rated supply voltage | 380…460 V – 15…10 % | |
motor power kW | 0.75 kW | |
motor power hp | 1 hp |
product destination | Asynchronous motors | |
---|---|---|
quantity per set | Set of 1 | |
EMC filter | Without EMC filter | |
supply frequency | 50/60 Hz +/- 5 % | |
communication port protocol | Modbus | |
connector type | RJ45 (on front face) for Modbus | |
physical interface | 2-wire RS 485 for Modbus | |
transmission frame | RTU for Modbus | |
transmission rate | 4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s | |
number of addresses | 1…247 for Modbus | |
communication service | Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43) | |
line current | 3.1 A | |
apparent power | 2.5 kVA | |
prospective line Isc | 5 kA | |
continuous output current | 2.3 A at 4 kHz | |
maximum transient current | 3.5 A for 60 s | |
power dissipation in W | 28.83 W at In | |
speed drive output frequency | 0.5…400 Hz | |
nominal switching frequency | 4 kHz | |
switching frequency | 2…12 kHz adjustable | |
speed range | 1…20 | |
transient overtorque | 170…200 % of nominal motor torque depending on drive rating and type of motor | |
braking torque | Up to 150 % of nominal motor torque with braking resistor at high inertia Up to 70 % of nominal motor torque without braking resistor | |
asynchronous motor control profile | Sensorless flux vector control Energy saving ratio Quadratic voltage/frequency ratio | |
motor slip compensation | Adjustable Preset in factory | |
output voltage | 380…460 V three phase | |
electrical connection | Terminal, clamping capacity: 1.5…2.5 mm² (L1, L2, L3, PA/+, PB, U, V, W) | |
tightening torque | 0.8…1 N.m | |
insulation | Electrical between power and control | |
supply | Internal supply for reference potentiometer: 5 V (4.75…5.25 V)DC, <10 mA with overload and short-circuit protection Internal supply for logic inputs: 24 V (20.4…28.8 V)DC, <100 mA with overload and short-circuit protection | |
analogue input number | 1 | |
analogue input type | Configurable current AI1 0…20 mA 250 Ohm Configurable voltage AI1 0…10 V 30 kOhm Configurable voltage AI1 0…5 V 30 kOhm | |
discrete input number | 4 | |
discrete input type | Programmable LI1…LI4 24 V 18…30 V | |
discrete input logic | Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm Positive logic (source), 0…< 5 V (state 0), > 11 V (state 1) | |
sampling duration | 10 ms for analogue input 20 ms, tolerance +/- 1 ms for logic input | |
linearity error | +/- 0.3 % of maximum value for analogue input | |
analogue output number | 1 | |
analogue output type | AO1 software-configurable voltage: 0…10 V, impedance: 470 Ohm, resolution 8 bits AO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bits | |
discrete output number | 2 | |
discrete output type | Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O | |
minimum switching current | 5 mA at 24 V DC for logic relay | |
maximum switching current | 2 A at 250 V AC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay 2 A at 30 V DC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay 3 A at 250 V AC on resistive load cos phi = 1 L/R = 0 ms for logic relay 4 A at 30 V DC on resistive load cos phi = 1 L/R = 0 ms for logic relay | |
acceleration and deceleration ramps | U S Linear from 0…999.9 s | |
braking to standstill | By DC injection, <30 s | |
protection type | Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t | |
frequency resolution | Analog input: converter A/D, 10 bits Display unit: 0.1 Hz | |
time constant | 20 ms +/- 1 ms for reference change | |
operating position | Vertical +/- 10 degree | |
height | 130 mm | |
width | 72 mm | |
depth | 143 mm | |
net weight | 0.7 kg |
electromagnetic compatibility | Electrical fast transient/burst immunity test – test level: level 4 conforming to EN/IEC 61000-4-4 Electrostatic discharge immunity test – test level: level 3 conforming to EN/IEC 61000-4-2 Immunity to conducted disturbances – test level: level 3 conforming to EN/IEC 61000-4-6 Radiated radio-frequency electromagnetic field immunity test – test level: level 3 conforming to EN/IEC 61000-4-3 Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11 Surge immunity test – test level: level 3 conforming to EN/IEC 61000-4-5 | |
---|---|---|
standards | EN/IEC 61800-5-1 EN/IEC 61800-3 | |
IP degree of protection | IP20 without blanking plate on upper part IP41 top | |
pollution degree | 2 conforming to EN/IEC 61800-5-1 | |
environmental characteristic | Dust pollution resistance class 3S2 conforming to EN/IEC 60721-3-3 Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3 | |
shock resistance | 15 gn conforming to EN/IEC 60068-2-27 for 11 ms | |
relative humidity | 5…95 % without condensation conforming to IEC 60068-2-3 5…95 % without dripping water conforming to IEC 60068-2-3 | |
ambient air temperature for storage | -25…70 °C | |
ambient air temperature for operation | -10…55 °C without derating 55…60 °C protective cover from the top of the drive removed with current derating 2.2 % per °C | |
operating altitude | <= 1000 m without derating |
Unit Type of Package 1 | PCE | |
---|---|---|
Number of Units in Package 1 | 1 | |
Package 1 Weight | 1.028 kg | |
Package 1 Height | 13 cm | |
Package 1 width | 18.6 cm | |
Package 1 Length | 19.2 cm |